Enerdrive 200Ah Off-Grid 40A AC & DC Charging Bundle, with 720W of Solar Panels and 2000W Inverter (AC Transfer)

Enerdrive 200Ah Off-Grid 40A AC & DC Charging Bundle, with 720W of Solar Panels and 2000W Inverter (AC Transfer)

Regular price $6,849.00 Sale

ENERDRIVE 200AH OFF-GRID 40A AC & DC CHARGING BUNDLE, WITH 720W OF SOLAR PANELS AND 2000W INVERTER (AC TRANSFER)

505 X 173 X 265MM (BATTERY) | 295MM X 206MM X 90MM (AC BATTERY CHARGER) | 1482 X 680 X 35MM (SOLAR PANELS) | 230 X 435 X 115 MM (INVERTER)

 

Included: 

  • Enerdrive ePOWER B-TEC 200Ah Lithium Battery EPL-200BT-12V-G2
  • Enerdrive ePOWER 12V 40A DC to DC Battery Charger EN3DC40+
  • Enerdrive ePOWER 12V 40A Battery Charger EN31240
  • Enerdrive ePRO PLUS Battery Monitor EN55050
  • Enerdrive ePOWER 2000W 12V Pure Sine Wave Inverter with RCD & AC Transfer Switch EN1120S-X
  • Enerdrive 180W Mono Crystalline Fixed Solar Panel (x4) SP-EN180W

 

Specifications: 

  • Amp Hours 200.0 Ah
  • Battery Voltage 12V 
  • Charger Mode Output Voltage 13.8V - 15.5V (DC Battery Charger) | 14.2 – 15.5 V (AC Battery Charger)
  • Float 13.50 - 13.80V (Battery) | 13.0V - 13.8V (DC Battery Charger) | 13.4 – 13.8 V (AC Battery Charger)
  • Equalize 15.5V (DC Battery Charger) | 16.0 V (AC Battery Charger)
  • Charging Control Four stages (Bulk/Absorption/Float/Maintenance), Two stages (Bulk/Absorption)Constant Power Supply (Program setting), Priority Battery Bank Charging (AC Battery Charger
  • DC Output Single (DC Battery Charger) | Three (1 fully independent, 2 common with diode isolation) (AC Battery Charger)
  • Selectable Battery Type Gel, AGM, Flooded, Lithium, Program (DC and AC Battery Charger)
  • Standby Current < 2 mA (AC Battery Charger)
  • Cell Type Monocrystalline - 72 Cells each (Solar Panels)
  • AC Input Voltage 90 to 265 VAC (AC Battery Charger)
  • AC Input Operating Range 207-265 Vac (3.8 A Max)90 – 125 Vac (7.7 A Max) (AC Battery Charger)
  • AC Input Frequency Range 47 – 63 Hz (AC Battery Charger)
  • Power Consumption 700W (Full Load) (AC Battery Charger)
  • Power Factor Correction Yes (AC Battery Charger)
  • Charger Efficiency 95% (DC Battery Charger) | > 82% (AC Battery Charger)
  • Reverse Polarity Yes, (with user replaceable fuse/s) (AC Battery Charger)
  • Over Charge Yes, unit shutdown (AC Battery Charger)
  • Over Temperature Protection Yes, unit de-rated and shutdown (AC Battery Charger)
  • Cooling Forced air ventilation (thermo controlled fan) (AC Battery Charger)
  • Output Short Circuit Yes, (with user replaceable fuse/s) (AC Battery Charger)
  • Temperature Setting Low/ Normal/ High (Battery Temperature Sensor Standard) (DC Battery Charger) | Hot, Normal, Cold (no sensor connected) (AC Battery Charger)
  • Battery Temperature Sensor Port RJ12 (standard battery temp. sensor supplied) (AC Battery Charger)
  • LCD Display Charging status, Battery Voltage, Output Current & Fault Codes (AC Battery Charger)
  • AC Input Connection IEC with Supplied 1.2M Power Lead (AC Battery Charger)
  • DC Output Connection Heavy Duty Terminal (3 banks) – Pan Heads 6mm Thread (AC Battery Charger)
  • DC Output Ground Single Heavy Duty Common Ground Stud (AC Battery Charger)
  • Storage Temperature Range -40° to 70° C (AC Battery Charger)
  • Operating Temperature Range -20° to 60° C (AC Battery Charger)
  • Humidity 5-95%, relative humidity non-condensing (AC Battery Charger)
  • Ingress Protection IP32 (Basic drip proof in vertical orientation) (AC Battery Charger)
  • Nominal Voltage 12.8V (Battery)
  • Nominal Capacity 200Ah (Battery)
  • Total Charge Current Max 150A @ 25°C for 30mins (Battery)
  • Regulatory Compliance Complies with AS/NZS 60335.2.29 Including Australian deviations
  • Cycle Life (DOD - 80% under controlled conditions) ≥ 2000 Cycles (Battery)
  • Battery Charge Temperature 0 ̴ 45°C (Battery)
  • Normal Charge Voltage CV/CC* 14.40 ̴ 14.60V (Battery)
  • Standby (Float) Voltage 13.50 ̴ 13.80V (Battery)
  • Maximum Charge Current 150A @ 25°C for 30mins (Battery)
  • Recommended Charge Current for Maximum Life ≤ 60A (Battery)
  • Battery Discharge Temperature -20 ̴ 60°C (Battery)
  • Battery Output Voltage Range 11.00 ̴ 14.60V (Battery)
  • Maximum Discharge Current 200A @ 25°C ± 5°C for 30mins (Battery)
  • Pulse Discharge Current 450A for 1.0s (Battery)
  • Discharge Cut-off Voltage ≤ 11.20V (Battery)
  • Input Voltage 12.5 VDC (Inverter)
  • AC Output 2000W, 8.7A (Inverter)
  • No Load Battery Draw < 1.2 ADC (Inverter)
  • Under Voltage Alarm 11.0/12.1 VDC (Inverter)
  • Under Voltage Alarm Recovery 11.3/12.3 VDC
  • Under Voltage Shutdown 10.5/11.8 VDC (Inverter)
  • Under Voltage Shutdown Recovery 12.0/12.6 VDC (Inverter)
  • Over Voltage Shutdown 15.5VDC (Inverter)
  • USB Socket Output 5V, 750 mA (Inverter)
  • Operating Altitude Up to 3000 meters above sea level (Inverter)
  • Wattage 180W each (720W toal) (Solar Panels)
  • Warranty 5 Years (Battery 5 Years)

 

Enerdrive ePOWER B-TEC 200Ah Lithium Battery:

The New Enerdrive Generation 2 (G2) B-TEC 200Ah Lithium Battery now comes with a 5 Year full replacement warranty. The ePOWER B-TEC is designed and intended for use in deep cycle applications where a single battery is required that meets the amp hour capacity.

Features: 

  • BMS restart button for easy recovery.
  • RS485 communications port for advanced system integration. 
  • Raised terminals for 360 degree cable connections.
  • Re-designed battery case for easy serviceability. 
  • Battery box and straps INCLUDED - nothing more to buy!
  • Product dimensions 505 x 173 x 265 mm

 

Smart Phone Monitoring System

The Enerdrive ePOWER B-TEC battery incorporates wireless Battery Monitoring Technology. By downloading the Android™ or Apple® app to your smartphone or tablet device, you can monitor the following information;

  • Battery Capacity
  • Battery Voltage
  • Battery Current (Amps)
  • Battery State of Charge (SOC)
  • Battery State of Health (SOH)
  • Battery Status
  • Individual Cell Voltage
  • Battery Temperature
  • Battery Cycles
  • Battery Alarms
  • Battery Event Information

 

Battery Management System

The battery is also equipped with an internal LiFePO4 Battery Management System (BMS) that can monitor and optimize each Prismatic cell within the battery during normal operation. It will protect the battery pack from over charge, over discharge, over temperature & short circuit. The BMS helps to ensure safe and accurate operation of the battery.

Size & Weight Savings
Lithium v AGM Capacities;

  • 200Ah Lithium = 360Ah AGM

(Based on standard depth of discharge for both Lithium (80%) and AGM (50%).

The ePOWER B-TEC battery provides 60% more usable power than its equivalent lead acid cousin and being nearly 50% lighter and 30% smaller makes for a superior alternative.

The ePOWER B-TEC battery is perfect for camper trailers, 4WD’s (AUX battery), caravans, small water craft, low power communication sites or any other application that requires the use of a single deep cycle battery that meets the amp hour capacity.

Please Note: This ePOWER B-TEC lithium battery is capable to be paralleled to a second ePOWER B-TEC lithium battery. For maximum performance and lifespan of your lithium battery, no more than 2 batteries should be connected together to increase your overall capacity. Overall loads when paralleled should not exceed the current limits of a single batteries BMS. 

 

Enerdrive ePOWER 12V 40A DC to DC Battery Charger:

The Enerdrive ePOWER DC2DC Battery Charger is a fully automatic multistage, multi input battery charger with the ability to charge from either an alternator linked to a battery; or via solar power with the in built Maximum Power Point Tracking (MPPT) Solar Controller.

EXPERT TIP: The Enerdrive 50Amp60Amp & 70Amp breakers are common accessories suitable for the Enerdrive EN3DC40+ 40A DC to DC charger. Additionally, the 3 pre-wired & fused charging cables are also a great extra accessories, see manuals & drawings for further information. All the accessories are available in the Accessory List above as optional extras.

Features:

  • Independent DC Inputs for both engine and solar regulation charging one house battery bank output
  • DC M6 screw terminals
  • A dedicated Maximum Power Point (MPPT) solar regulator
  • The same battery algorithms as included in our AC mains ePOWER battery charger including a specific lithium charging profile
  • 40A output up to 40+°C with thermo controlled fan cooling
  • Fully programmable LCD display
  • Temperature sensor 

 

Enerdrive ePOWER 40A Battery Charger:

The Enerdrive ePOWER 40A Battery Charger is a fully automatic, “set and forget” charger. It is designed to quickly and accurately recharge your batteries using algorithms that help maximise service life. Multistage smart charging technology enables the charger to be connected to your battery banks permanently.As dictated by battery manufacturer’s recommendations, batteries require a multistage charge sequence for perfect, fast and accurate charging. The Enerdrive ePOWER charger can be programmed for Lithium batteries. This setting delivers the full rated output of the charger constantly with the charger switching to power supply mode once the voltage peak is met (indicating a full battery bank).

Features:

  • Fully automatic multistage battery charger with the ability to charge 3 separate battery banks
  • Isolated charging design where battery bank one is separate from battery bank two and three
  • Battery bank 1 can be programmed with a different charge algorithm over banks 2 and 3
  • Current Control
  • Smart Charging
  • Operates on both 110V / 60Hz and 240V / 50Hz
  • LED Display
  • Silent Mode
  • Battery temperature sensor included with 3 meter cable
  • 5 Year Warranty 

 



Enerdrive ePRO PLUS Battery Monitor:

The ePRO PLUS is the latest generation, highly advanced battery monitor. It consists of an intelligent shunt and a remote control display unit. The shunt has a Grid Optimized footprint for perfect integration with our DC Modular products. This advanced battery monitor not only shows the true state of charge of your battery system. It also offers a large amount of additional features to optimally supervise your battery system and control external equipment. The ePRO PLUS is compatible with lead based and Lithium batteries (LiFePO4).

The ePRO PLUS can monitor up to three battery banks. The inputs for battery bank 2 and 3 can also be configured for other purposes, like mid-point voltage measurement, keyswitch input, setup lock or backlight control. The ePRO PLUS battery monitor can measure DC currents up to 600Amps (500Amp continuous) and voltages up to 70Vdc. So any lead- or lithium based battery from 12V up to 48V can be monitored. The installation time is minimal, requiring only one supply wire to the intelligent shunt base and a single ‘QuickLink’ cable between the shunt base and the control/display unit (CDU). Additionally, the battery minus cable must be interrupted in order to insert the shunt into the high current circuit. The fused supply wire and the QuickLink cable are both included in the package, avoiding the need for a separate connection kit.

Features: 

  • Complete battery status information at a glance 
  • Supports up to three battery banks (12V, 24V and 48V)
  • ‘Plug and Play’ installation
  • Perfect integration with Enerdrive DC Modular products

 

 

Enerdrive ePOWER 2000W 12V Pure Sine Wave Inverter with RCD & AC Transfer Switch:

The ePOWER 2000W Inverter incorporates a 16A AC Transfer Switch which allows for seamless AC power transfer between Mains/Generator and Inverter. This helps to keep your appliances running with almost no break time on AC transfer and allows for a much simpler installation on-board. This inverter is built to operate basic equipment such as power tools, computers, microwave ovens, televisions and other appliances that use up to 2000W of power for operation. The inverter offers reliable service for providing AC power for your home, boat, 4WD, truck or Caravan.

The AC Transfer Cable is now included with all AC Transfer Switches. Inverters is a 4 metre AC lead with molded Male/Female IEC Plugs fitted. This allows the installer to cut the lead and hardwire the IEC plugs directly. This will speed up installation time and eliminate any connection issues within the plug.

 

Features: 

  • Seamless 16A AC Internal Transfer Switch
  • AC RCD/Safety Switch with test button
  • Removable LED Remote Control Display Panel
  • Regulated Pure Sine Wave Output
  • Silent Operation
  • Compact Size for Easy Installation
  • USB Port for charging USB devices
  • PS6 Mode
  • AC Transfer Cable
  • 5 Year warranty
  • ePOWER Enerdrive Inverters with AC Transfer Switch now include the new PS6 mode

 

 
 

Enerdrive 180W Mono Crystalline Fixed Solar Panel (x4): 

Features: 

  • Suited to 12v installations (or 24v by series connections of panels)
  • A fly lead cable is provided for easy connection of the 10 & 20w panels 
  • The larger panels have MC4 compatible solar cable connectors included